Stepper Motor NEMA 34 87 kg-cm Hybrid Bipolar
Features
- Step Angle Step Angle: 1.8 °
- Current: 5 A/Phase
- Holding Torque: 870 N-cm
- Lead Wires: 4
- Shaft diameter: 14 mm.
STM32F103C8T6 ARM board
Features
- 2.0-3.6V power, I/O.
- Operating voltage:3.3V
- Analog inputs:10
- Digital I/O pins:37
- DC source/sink from I/O pins:6mA
- Flash memory (KB):64/128
- SRAM:20KB
- Frequency (clock speed):72MHz max.
- Communication:I2C, SPI, UART, CAN, USB
Sunny Sky A2212 980 kv
Features
- Poor man’s Tiger motor
- Brand name: Sunnysky
- KV: 980KV.
- Framework: 12N14P
- Operating Current: 6A ~ 18A
- Peak Current: 14A
- Shaft: 3mm.
- thrust: 880g
- Stator Diameter: 22mm
- Stator Thickness: 12mm
- of Stator Slots: 12
Super Mini Elm327 V2.1 Bluetooth Obd2 OBD-Ii Car Auto Diagnostic Scanner Android
Features:-
- Engine RPM
- Calculated Load Value
- Coolant Temperature
- Fuel System Status
- Vehicle Speed
- Short Term Fuel Trim
- Long Term Fuel Trim
- Intake Manifold Pressure
- Timing Advance
- Intake Air Temperature
- Air Flow Rate
- Absolute Throttle Position
- Oxygen sensor voltages/associated short term fuel trims
- Fuel System status
- Fuel Pressure.
Super:bit expansion board for BBC Micro Bit Pocket Sized – Single Board Computer
Features:-
- Nordic Semiconductor nRF52833 processor
- Notched edge connector to make it easier to connect things like crocodile clips and also conductive thread.
- Power LED indicator in addition to the USB activity indicator.
- Gold plated antenna to easily identify the radio and Bluetooth component.
Swappable Power Pod Kit
Swappable Power Pod Kit with Landing gear and wheels
TAP Sensor Module
Features
| Brand/Manufacturer | Generic |
| Country Of Origin | China |
| Packer / Importer Address | Constflick Technologies Limited, Building No 13 and 14, 3rd Floor, 2nd Main, Siddaiah Road, Bangalore, Karnataka – 560027 India. |
| MRP | Rs. 55.46 (Inclusive of all Taxes) |
Tauren Gear series 100 – 30 rpm
Features
| Maximum Speed(RPM) | 30 (at 12V) |
| Rated Voltage | 12V |
| Nominal Voltage | 12V |
| Stall Torque(Kg-Cm) | 90 kgcm |
| No Load Current | 700 mA |
| Rated Load Current | 4 A |
| Stall Current | 14 A |
| Weight (gm) | 500 gram |
Tauren Gear series 100 – 300 rpm
Features
| Maximum Speed(RPM) | 300 (at 12V) |
| Rated Voltage | 12V |
| Nominal Voltage | 12V |
| Stall Torque(Kg-Cm) | 14 kgcm |
| No Load Current | 700 mA |
| Rated Load Current | 4 A |
| Stall Current | 14 A |
| Weight (gm) | 500 gram |
Tauren Gear series 100 – 600 rpm
Features
- Rated Voltage – 12v
- RPM – 600 (at 12v)
- Nominal Voltage – 12v
- No- Load Current – 700 mA
- Load Current – 4 A
- Stall Current – 14 A
- Full (Stall) Load Torque – 14 kgcm
- Weight – 500g Approx
tb6560
Features
- Operating voltage :DC 10V-35V
- Very easy to use, no instructions, all of use are marked on the board
- With large heat sink to ensure good heat dissipation
- Input signal high-speed opto-coupler isolation, guarantee not losing steps
- Semi-flow mode adjustable, semi-flow current adjustable, not the general design on the market, with a variety of semi-flow model and semi-flow current setting function
- Attenuation model adjusted for all the motors can be locked when no noise
- Working voltage: DC 10V-35V. Recommend Switching Power Supply DC24V
- 6N137 high-speed Opto-Coupler, to ensure a high speed without step out.
TB6560 4 Axis Cnc Controller 4 Axis Stepper Motor Driver DSP Controlled 3.5A 24V
Features
- Rated maximum output: ± 4.5A, 40V, Peak 5A, low output impedance, source 0.5?,
- the receiving end of 0.4?, low voltage shutdown, thermal parking and circulation.
- circuit protection. After I design, you can set the current output of 0.5A 1A 1.8A 2.5A.
- 3.3A 4A 4.5A to accommodate more and different motor Current.
- The drive is suitable software mach2, mach3, (mach3 have support WIN7 system), KCAM4 like.
TB6560 CNC 3 Axis Stepper Motor Driver Controller Board For Mach3 KCAM4 EMC2 36V
Features
- Electrical properties (ambient temperature Tj = 25 pm)
- Input Power 12 – 36V DC power supply
- Stepper motor drive current
- 3A (peak value 3.5A)/axis
- Drive type
- Double-pole constant flow PWM actuation output
- Compatible Stepper motors
- 2/4 Phase, 4/6/8 leads stepper motors within 3.5A.
TB6600
Features
- Support 8 kinds of current control
- Support 7 kinds of micro steps adjustable
- The interface adopts high-speed optocoupler isolation
- Automatic semi-flow to reduce heat
- Large area heat sink
- Anti-high-frequency interference ability
- Input anti-reverse protection
- Overheat, over current and short circuit protection.
Tb6612Fng Dual Motor Driver Module for Arduino/Other Microcontroller
Features
- CW/CCW/short break/stop motor control modes
- Built-in thermal shutdown circuit and a low voltage detecting circuit
- Standby control to save power
- CW/CCW/short brake/stop motor control modes
- Operating Voltage(VDC): 15
- Peak Current (A): 3.2
- Continuous Current (A): 1.2
- No. of Channels: 1.
TCRT5000
Features
- Operating Voltage: 3.5V-5V
- Supply Current: 15mA
- Optimal Sensing Distance: 3mm
- Designed with the reflected infrared sensor, indicator light.
- Built in a potentiometer for sensitivity control.
- On-board LM393 voltage comparator chip and infrared sensing probe TCRT5000L
- Signal detection sensitivity can adjust
- Reserve all the way more circuits (P3 voltage drawn)
TCRT5000 Module
Features
- The working voltage: 5V
- A fixed bolt hole for easy installation
- Build-in Tcrt5000 Sensor NSOR
- Applicable to a variety of platforms including Arduino / AVR / ARM /PIC
TDA7266 dual audio channel 7w + 7w amplifier module power amplifier module
Features:
- Operating Voltage Range: 3 V to 18 V
- Power supply:14W
- On-board TDA7266 stereo audio amplifier chip
- Output: dual-channel 7W + 7W
- On-board 5.08 mm terminal blocks for the left and right audio channels
- On-board potentiometer for volume adjustment
- DC power jack
- Minimum external components.
TDA7492 Wireless 4.0 2 * 50W 2-Channel Audio Receiver Stereo Digital Power Amplifier Board Module
Features:-
• Class D amplifier produces 2 x 50 watt @ 8 ohms
• Can be wired R+ to L+ for mono mode
• 8″ stereo wiring harness included
• Short-circuit and over-temperature protection
• Supply Voltage 10-26 V DC.
• Standby and mute features
• Short-circuit protection
• Thermal overload protection
• Externally synchronizable.
TDA7492P 50W Wireless Bluetooth 4.0 Audio Receiver with Digital Amplifier (Multicolor)
Features:-
- 25 W + 25 W continuous output power at THD = 10% with VCC= 20 V and RL= 8 Ω
- Wide-range single-supply operation (8 – 26 V)
- High efficiency (η = 90%)
- Four selectable, fixed gain settings of nominally 21.6 dB, 27.6 dB, 31.1 dB and 33.6 dB
- Differential inputs minimize common-mode noise
- Standby and mute features
- Short-circuit protection.
TDA7498E Double 160W Power Amplifier Dual Channel Stereo Audio Amplifier Module Support BTL Mode
Features:-
- Amplifier chip: TDA7498E
- Working voltage: DC 15-36V (Recommend 32V, 8A, if power is too small will appear distortion and so on.)
- Output power: 2 x 160W
- Number of channels: Two-channel Stereo
- Efficiency: 85%
- Applicable speaker impedance: 4/6/8ohm (8ohm is the best).
- 160-W + 160-W output power at THD = 10% with RL = 4 Ω and VCC = 36 V
- 1 x 220 W output power mono parallel BTL at THD = 10% with RL = 3 Ω and VCC = 36 V
- Wide-range single-supply operation (14 – 36 V)
- High efficiency (η = 85%)
- Parallel BTL function using the MODE pin
- Four selectable, fixed gain settings of nominally 23.8 dB, 29.8 dB, 33.3 dB and 35.8 dB
- Differential inputs minimize common-mode noise
- Standby and mute features.
TEC1-12705
Features
- Model number: TEC1-12705
- Operating Voltage: 12V
- Maximum Voltage- Umax (V) : 15V
- Maximum Current- Imax (A) : 5.2A
- Maximum Power : 54 W
- Power Cord: 25cm
TEC1-12706
Features
- Model number: TEC1-12706
- Operating Voltage: 12V
- Maximum Voltage Umax (V) : 15.4V
- Maximum Current Imax (A) : 6A
- Maximum Power: 92 W
- Maximum Temperature: 138°C
- Power Cord: 200mm
TEC1-12715
Features
- Model number: TEC1-12715
- Operating Voltage: 12V
- Maximum Voltage- Vmax (V) : 15V
- Maximum Current- Imax (A) : 15A
- Maximum Power : 230 W
- Power Cord: 100mm
- Quality tested cooling cells.
- Solid state, vibration free, noise-free.
- Simple to install and operate.
TEVO Tarantula I3 Aluminium Extrusion 3D Printer kit printer 3d printing
Features:
- Layer resolution of 50 microns.
- MAX Printing Speed: 150 mm/s.
- Build size: 200X 200 X 200mm.
- Full Metal Bowden Extruder.
- Material type: PLA, ABS, PETG, Wood, PVA and Flexible Filaments (With Pro Metal Extruder).
- Material specifications 1.75mm in diameter.
- Positioning accuracy: Z 0.04mm, XY 0.012mm.
- Printing Color: Single color.
- Nozzle diameter: 0.4mm.
- Recommended extruder temperature: 210°C (the maximum can be set to 260°C).
- Heating plate temperature: 60-120°C (proper winter warming and summer appropriate cooling).
- Best ambient temperature: +/-25°C.
- Power requirements: 220V, 250W, 50Hz, 0.89A.
Throttle
Features
Red Supply
Black GND
Green Signal
Throttle with Battery Indicator & Ignition – BE0301
Features:-
- Working Voltage: Throttle(DC) 1V to 4.2V, Battery Level Indicator 12V to 84V
- Throttle for all E-bikes/Bicycles
- Fit for 22.2mm diameter handle
- Shows battery voltage up to 0-100V
- ON/OFF Key Switch Feature.
Throttle with Battery Indicator & Ignition – BE0302
Features:-
- Throttle Type: With LCD Display
- Material: ABS/PMMA
- Waterproof Lever: IP54
- Voltage: 36V
Throttle with Battery Indicator, Power lock key & Ignition – BE0303
Features:-
- Throttle Type: With LCD Display
- Material: ABS/PMMA
- Waterproof Lever: IP54
- Voltage: 36V
Thumb Throttle with Battery Indicator, Power lock key & Ignition – BE0304
Features:-
- Item Type: E-Bike Voltage Display
- Material: Plastic
- Color: As Picture Shown
- Model: (5V-99V Automatic Identification of Electric Vehicle Voltage)
- Efficiency: 98% or Higher Hall
- Grade: Linear Hall High-Quality Rubber Imported LED Digital Display Lamp Working
- Voltage: Turn DC0.8V-4.2V Power
- Display:12V, 24V, 36V, 48V, 60V, 72VÂ
- Length: 1.5m.
Thumb Throttle with Battery Indicator, Power lock key & Ignition – BE0305
Features:-
- Item Type: E-Bike Voltage Display
- Material: Plastic
- Color: As Picture Shown
- Model: (5V-99V Automatic Identification of Electric Vehicle Voltage)
- Efficiency: 98% or Higher Hall
- Grade: Linear Hall High-Quality Rubber Imported LED Digital Display Lamp Working
- Voltage: Turn DC0.8V-4.2V Power
- Display:12V, 24V, 36V, 48V, 60V, 72VÂ
- Length: 1.5m.
Titanium HSS 9-Step Cone Drill 4-12MM Hex Shank 1/4 Hole Cutter Drilling Tool
Features:-
- Shank: 1/4 Hex Shank
- Comes in 4-12MM ( 4,5,6,7,8,9,10,11,12MM )sizes
- Material: HSS
- The ladder of its unique structure, a bit can open a variety of specifications of aperture.
- No need to use center punch, compared with the ordinary twist drill is not easy to be broken.
- Deburring, chamfering, elliptic hole enlargement, twist drill, the function of them was unable, but it is possible.
- The usage of tools: drill, bench drill. Work while water cooling can effectively extend the service life of drill bit
- Do not need to use center punch, compared with the ordinary twist drill is not easy to be broken.
- Deburring, chamfering, elliptic hole enlargement, twist drill, the function of them was unable, but it is possible.
- Size: Approx. 72mm
- Weight: 21g.
TL866II Plus Universal USB MiniPro USB Programmer for 15000+IC SPI Flash NAND EEPROM MCU PIC AVR
Features:-
- High-Speed Programming – 12 Mbps
- Unique ultra-low power consumption
- Portable performance
- Programmable programming power supply
- Best overvoltage, overcurrent protection
- 40-pin universal pin
- Upgrade function
- 54/74F/LS/HC CMOS4000 series IC functional tests
- AVR microcontroller one-to-one soft encryption
- Unified and convenient user interface
- NAND Flash: Yes.
TL866II Plus USB Programmer Support 15000+IC SPI Flash NAND EEPROM MCU PIC AVR Replace TL866A TL866CS
Features:-
- Model: TL866II Plus
- With Multi-functional ICSP interface
- 40pin ZIF socket, fully automatic, support fast mode SPI
- USB interface for both data transfer and power supply
- With over-voltage and over current protection.
TowerPro SG92R Mini Micro Servo 9g 2.5kg
Features:
- Model: SG92R
- Weight: 9 gm
- Operating voltage: 3.0V~ 7.2V
- Servo Plug: JR
- Stall torque @4.8V : 2.5kg-cm.
TPA3116D2 100W Channel Digital Power Audio Stereo Amplifier Board and DC 12-24V Car Stereo AMP Module for Audio System with Volume Knob
Features:-
- With DC power supply connection port and DC 12-24V wiring terminals (please do not use in the same time)
- 3.5mm audio input jack
- 3-pin audio input jack
- Volume/ Subwoofer/ Stereo knob adjustment,DC 12-24V power supply audio amplifier
- great for connecting to telephone or computer.