The 1000mm Trapezoidal 4 Start Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut used for general machine tools such as 3D printing.

It has good wear resistance and strength, high accuracy, hard to rust and has good performances due to low friction coefficients and long usage spans. This Trapezoidal Lead Screw with Copper Nut is a new type of screw which is mainly used in stepper motor, machine tool rails and other types of equipment.

This All complete Bowden V6 with Fan Cable 30cm Length for 1.75 mm filament 0.2 mm Nozzle contains the same signature high-temperature performance for high-temp printing, as well as increased functionality for printing soft and flexible filaments. This kit contains the old thermistor, heater block, sleeving, cooling fan with holder.

The v6 HotEnd allows you to print a wide variety of materials, from soft and flexible to sturdy and strong. This is possible due to the PTFE (Polytetrafluoroethylene) liner tube through the hotend that you can extend into your extruder – this gives the ability to add the confinement and constraint needed to make excellent quality prints with flexible filaments. This technology opens new doors for your 3D printing aspirations.

With High-Temperature Performance, you can print with high-temp materials like Polycarbonate and Nylon – this also eliminates HotEnd meltdown failures that are common with PTFE designs. Even though the v6 has a PTFE liner inside the hotend the liner is never subjected to high temperatures so there is no risk of damaging the liner through overheating. Basically, this design is really in-tune with all the elements, so your prints will come out crisp and accurate.

The v6 has cut back on a bunch of bulk. This clean-cut version’s overall length is only 62mm, and there are significant reductions in the X/Y dimensions by using the new injection moulded fan duct.

Are you eager to start printing right away? Good. So are we – and that’s why here at MatterHackers we praise the v6 HotEnd. No adhesives, Kapton tape, or soldering is needed to get started. The new v6 simply locks into place with a little screw, high-temp glass sleeving is used to insulate the thermistor legs. This makes installing the hotend (as well as removing) a quick and smooth process compared to earlier methods involving various adhesives. The parts of the hotend just screw together, and the fan duct naturally clips in – this can be manipulated in different ways to suit your setup preference.

The stepper motors move in precisely repeatable steps, hence they are the motors of choice for the machines requiring precise position control. The NEMA17 4.2 kg-cm Stepper Motor can provide 4.2 kg-cm of torque at 1.2A current per phase.

The motor’s position can be commanded to move or hold at one position with the help of Stepper Motor Drivers. The NEMA17 4.2 kg-cm Stepper Motor provides excellent response to starting, stopping and reversing pulses from stepper motor driver.

They are very useful in the various application, especially which demands low speed with high precision. Many machines such as 3D Printers, CNC Router and Mills, Camera Platforms, XYZ Plotters etc.

It is a brushless DC motor, so the life of this motor is dependent upon life of the bearings. The position control is achieved by a simple Open Loop control mechanism so doesn’t require complex electronic control circuitry.

It comes with a detachable 70cm cable which makes wiring and rewiring very fast and easy work. The design of this cable is such that it can directly be mounted on a stepper motor controller. So, playing with the connection is done with just snap of fingers.

The motor’s shaft has been machined for good grip with a pulley, drive gear etc., and especially avoiding stall or slip.

We are engaged in supplying and wholesaling a quality approved collection of the Stepper Motors which are highly acknowledged and accepted for long service life and high reliability. To explore more of them click below, 

Stepper Motors

Note :

1. The Nema17 4.2kgcm Stepper motor dimensions and weight may have  ±2% error.
2. Resonances can occur because of improper installment.
3.  Not easy to operate at extremely high speeds.

The 500mm Trapezoidal 4 Start Lead Screw 8mm Thread 2mm Pitch Lead Screw with Copper Nut used for general machine tools such as 3D printing.

It has good wear resistance and strength, high accuracy, hard to rust and has good performances due to low friction coefficients and long usage spans. This Trapezoidal Lead Screw with Copper Nut is a new type of screw that is mainly used in stepper motor, machine tool rails and other types of equipment.