Showing 469–504 of 1014 results
Features:
- Maximum operating speeds up to 2Mbps
- GFSK modulation efficiency, Anti-interference ability,
- Built-in hardware CRC error detection, Multipoint communication address control.
- Low-power 1.9 to 3.6V, only 1uA on Power-down mode
- Built-in 2.4Ghz antenna
- Built-in voltage regulator.
Features:
- Material: Aluminum.
- Number of teeth: 20.
- Pitch: 2mm (GT2)
- Bore diameter: 6.35mm
- Belt width: 10mm.
- Outside diameter: 16mm
- Length: 19.5mm.
- Weight: 10 gm.
Features:
- Material: Aluminum.
- Number of teeth: 20.
- Pitch: 2mm (GT2)
- Bore diameter: 8mm
- Belt width: 10mm.
- Inner Diameter: 8mm.
- Outside diameter: 14mm
- Length: 18.1mm.
- Weight: 10 gm.
Features:
- Material: Aluminum.
- of teeth: 20.
- Outer Diameter: 16mm.
- Inner Diameter: 8mm.
- Length: 16 mm.
- Weight: 10 gm.
Features:
- Material: Aluminum.
- No. of teeth: 20.
- Outer Diameter: 16 mm.
- Inner Diameter: 6.35mm.
- Length: 16 mm.
- Weight: 6 gm.
Features:
- The degree of Freedom (DOF): 2
- Paw material: aluminum alloy
- Paw weight: about 68g (without motor)
- Claws overall length: 108mm (overall maximum length when closed paw)
- Claws overall width: 98mm (maximum overall width of the paw when open)
- Paw maximum opening angle: 55mm.
Features:
- Motor Type: DC Motor
- Gear Type: Copper
- Stall Torque: 15.5 kg-cm (4.8V); 17.0 kg-cm (6V)
- Operating Speed: 0.16sec/60degree (4.8V); 0.14sec/60degree (6.0V)
- Temperature Range: -20℃ – +60℃
- Working Frequency：1520μs / 50Hz
- Servo Wire Length: 32cm
- Current Draw at idle: 10mA
- No Load Operating Current: 170mA
- Stall Current: 1.2A.
Features:
- Name: PS-5521MG Analog Servo
- Maximum Angle: 90°
- Gear: Metal
- Operating Voltage:4.8V-6V
- Dead band: 7µs 1520µs / 50hz
- Operating Speed (4.8V): 0.18 sec/60°
- Operating Speed (6V): 0.16 sec/60°
- Stall Torque (4.8V): 17.25 kg.cm (239.55oz/in)
- Stall Torque (6V): 20.32 kg-cm (281.89 oz/in)
- Connector Wire Length: JR 265 mm (10.43in)
- Bearing: 2BB
- Dimension: 40.5×40.3x20mm
- Weight: 85.
Features:
- Capacity : 50.kg
- Output Sensitivity (mv/v): 1.0±0.1.
- Nonlinearity (%FS): 0.03.
- Repeatability (%FS): 0.03.
- Input Resistance: 1000. Ω
- Insulation Resistance : ≥5000.MΩ
- Alloy Steel wired weighing load cell
- High Accuracy
- Simple Structure & Easy Installation.
- Internal 1000 Ω half-bridge strain gauge load cell, the range is 50kg, half-bridge structure
- You can use multiple load sensors simultaneously to increase the capacity range, Parallel use to add additional capacity.
Features:
- Supported Motors: 10kg-cm servos (such as MG995, MG996)
- No of Axis: 2 axis
- Weight : 51.2gms
- No of Metallic Pieces: 2
- This product is made of high-quality materials and is durable.
- Various sensors can be installed to complete a variety of novel interactive works through the servo controller.
- It is convenient to install the camera, which can realize image monitoring and image recognition and tracking.
Features:
- Material: Aluminium
- M3 Screws
-
Adjustable type servo arm
-
Mounting Hole Spacing: 14mm
-
Servo disc diameter: 20mm
- 25Tooth
- Weight: 2 gm.
Features:
- Model: SC16LUU
- Ball Circuit: 4
- Inner Diameter (mm): 16
- Length (mm): 85
- Outer Casing: Chromium Steel
- Linear bearing ball cage, hardened coat of both ends ring.
- Safe and reliable operation.
Features:
- Model: SG92R
- Weight: 9 gm
- Operating voltage: 3.0V~ 7.2V
- Servo Plug: JR
- Stall torque @4.8V : 2.5kg-cm.
Features:
- Material: Mild Steel(MS)
- Weight: 5 gm (each)
- Length: 35 mm
- Width: 37 mm
- Thickness: 2.7 mm.
Features:
- Teeth Number: 25T
- Color: Silver
- High-quality and durable in performance.
- Lightweight and portable to carry
- It has an aluminum body and is perfect for servos with 25 teeth.
Features:
- Operating Voltage: 3-6V VDC
- Gear Ratio: 1:48
- No-load speed(5V): about 200 RPM
- Rated Torque: 0.8 Kg.cm @ 5V
- Load current: 170mA (when it is 4.5V)
- Shaft Length: 10 mm
- Shaft Type: 6 mm, Double-D
- Loading Capacity: Max 2.5Kg
- Wheel Diameter: 65 mm
- Wheel Width: 27 mm
- Body Material: Plastic
- Grip Material: Rubber.
Features:
- Tire with sponge liner for more strength
- With upgraded tire tread for greater friction
- New design wheel for better combination with the motor
- Diameter: 65 mm
- Width : 28 mm
- The material of Wheel: High-strength plastic
- The material of Tyre: Rubber
- Color: Yellow.
Features:
- Meet UL, CE requirements,
- Ultra-thin, ultra-small
- All voltage input (AC: 90 ~ 264V)
- Low ripple and low noise
- Output overload and short circuit protection
- High efficiency, high power density
- The product is designed to meet the requirements of EMC and Safety Test.
Features:
- Meet UL, CE requirements,
- Ultra-thin, ultra-small
- Rated input voltage 100-240 VAc
- Input voltage range 90-264 VAc
- Maximum input current: 0.2 A
- Input current surge: 10 A
- Maximum Input voltage: 270 VAc
- Enter slow start:50 mS
- Input Low Voltage Efficiency Vin=110VAc,Output full-load?69 %
- Input High Voltage Efficiency Vin=220VAc,output full-load?70 %
- Long-term reliability: MTBF 100000h.
Features:
- TTL serial port for serial port, you can link directly to the micro-controller.
- Don’t need MAX232.
- Power module automatically boots, homing network.
- Onboard signal lights all the way.
- It flashes slowly when there is a signal, it flashes quickly when there is no signal.
Features:
- Operating Frequency Range: 433.4—473.0MHz
- Transmit Power Max: 20dBm
- Power Supply Voltage: DC 3.2V ~5.5V
- Long Communication Distance: About 1000 meters at the default setting.
Features:
- CPU and Memory: Xtensa® 32-bit LX6 Dual-core processor, up to 600 DMIPS.
- 448 KByte ROM
- 520 KByte SRAM
- 16 KByte SRAM in RTC.
- QSPI can connect up to 4* Flash/SRAM, each flash should be less than 16 Mbytes.
- Supply Voltage: 3V~3.6V.
Features:
- Working voltage: 3.3V-4.2V
- Power voltage> 3.4V
- Standby average current: 3mA
- Working temperature: -30 to + 80
- Supports Quad-band: GSM850, EGSM900, DCS1800 and PCS1900
- Connect onto any global GSM network with any 2G SIM
- Make and receive voice calls using an external 8Ω speaker & electret microphone
- Facility to connect 4-pole TRRS mic and headset
- 8V UART port level – compatible with Arduino, Raspberry-Pi
- Supports serial-based AT Command Set
- Accepts Micro SIM Card.
Features:
- Protocol: ZigBee
- Modulation: DSSS
- Frequency: 2.4GHz
- Data Rate: 1Mbps
- Power: Output 18dBm
- Sensitivity: 101dBm
- Serial Interfaces: SPI, UART
- Antenna Type: Antenna Not Included, U.FL
- Transceiver chipset: Silicon Labs EM357 SoC
- Operating voltage: 2.7V-3.6V
- Current Receiving: 31mA ~ 45mA.
Features:
- Supports binding and multicasting for home automation
- Mesh-network topology
- 2.4 GHz for worldwide deployment
- Common XBee footprint fits Parallax XBee Adapters and the Propeller Activity Board
- Firmware upgrades via UART, SPI or over the air
- TRANSCEIVER CHIPSET: SiliconLabs EM357 SoC
- DATA RATE: 250kbps Max
- RATED OUTDOOR/RF LINE-OF-SIGHT RANGE: Up to 2 mile (3200m).
Features:
- Integrated, Wire Antenna
- Interoperable with other ZigBee-compliant devices
- Programmable versions with onboard microprocessor enable custom ZigBee application development
- Supports binding and multicasting for easy integration into a home automation platform
- Data Rate: RF 250 Kbps, Serial up to 1 Mbps
- Range: Indoor 200 ft (60 m), Outdoor (LOS) 4000 ft (1200 m)
- Transmit Power: 3.1 mW (+5 dBm)
- Channels: 16 channels.
Features:
- Compatible with all ZigBee modules (Series 1 and Series 2.5, standard and Pro)
- The built-in 3V3 Voltage regulator
- Onboard 3V3 <->5V level converter (easy to interface 5V Devices)
- Status LEDs ( RX,TX,RSSI,Power)
- Zig Bee Pins available at 2.54 mm berg strip
- All XBee pins are broken out.
- Reset button.
Features:
- 5Hz position update rate.
- The cold start time of 38 s and Hot start time of 1 s.
- Configurable from 4800 Baud to 115200 Baud rates. (default 9600).
- SuperSense ® Indoor GPS: -162 dBm tracking sensitivity.
- Support SBAS (WAAS, EGNOS, MSAS, GAGAN).
- Separated 18 x 18mm GPS antenna..
Features:
- 2.4GHz 802.11b/g/n,compatible
- Support IEEE 802.3、IEEE 802.3u
- WiFi Client/AP/Router Mode
- Support WPS/WDS
- The range of baudrate: 1200~500000bps.
Feature
- Operating voltage: 3.0V to 4.2V
- Ultra high sensitivity: -165dBm
- Extremely fast TTFF (Time To First Fix) at the low signal level
- Low power consumption: Typical 45mA@3.3V
- NMEA-0183 compliant protocol or custom protocol
- Operating temperature range: -40 to 85℃
- SMD type with stamp holes
- Small form factor: 15x13x2.7mm
- RoHS compliant (Lead-free)
- Support walk model.
Feature
- 6-channels GPS search engine
- Ultra low power design (38mA, typical)
- Compact size
- Built-in low noise, high gain active antenna
- Super-cohesive magnetic for installation
- High sensitivity (up to -152dBm typ)
- Apply to host devices with USB or RS232.
Feature
- Material: ABS
- Response Frequency: 125Khz
- 2kbps ASK
- Diameter: ~29mm
- Range: 0-10 cm
- Manchester encoding
- 32-bit unique ID
- Uses TK4100 chip which is compatible with EM4100
- 64-bit data stream [Header+ID+Data+Parity]
- Read Time: 1-2ms.
Feature
- Material: ABS
- Dimension(LxWxH): 43.7×30.5×5.3mm
- Response Frequency: 13.56MHz
- Chip type: FM1108 Fudan Chip
- Memory capacity: 8 kbit
- Designed for the RFID 13.56MHz duplicator. can copy all the ID card, such as Access Card, District Card, Parking etc.
Feature
- Wide input supply (2.5 V to 12V)
- Easy to integrate (V+, GND, and Data)
- The device in deep sleep mode when Data pin is grounded
- Very small dimension.
Feature
- Maximum effective distance up to 150mm
- Less than 100ms decoding time
- Support external antenna
- UART interface
- Support EM4100 compatible read-only or read/write tags
- Small outline design.
Feature
- Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability,
- Particularly suitable for industrial control applications.
- Built-in hardware CRC error detection, Multipoint communication address control.
- Low-power 1.9 ~ 3.6V, only 1uA on Power down mode
- Built-in 2.4Ghz antenna
- Built-in voltage regulator
- Standard DIP Pitch Interface for embedded applications.
