Features:-

• 7 x 7 mm Cable drag Chain With End Fits
• Radius: 15mm
• Miniature series 7-non opening type
• HI:7mm BI:7mm H:10mm BA:13mm
• Pitch=16.7mm Link Per Meter=58
• Max outer diameter of cable:5mm
• 1-meter length
• Long operating life
• Good toughness
• High performance.

Features

1. Rated voltage: 5V DC
2. Reduction Ratio: 64:1
3. Step Angle: 5.625° /64
4. Frequency: 100Hz
5. Self-positioning Torque: >34.3mN.m
6. Friction torque: 600-1200 gf.cm
7. Pull in torque: 300 gf.cm.

Features

1. Rated voltage: 5V DC
2. Reduction Ratio: 64:1
3. Step Angle: 5.625° /64
4. Frequency: 100Hz
5. Self-positioning Torque: >34.3mN.m
6. Friction torque: 600-1200 gf.cm
7. Pull in torque: 300 gf.cm.

Features

1. Supply Voltage : 8-35 VDC.
2. Current : 1.0A  (no heatsink ).
3. Current : 2.0A (with heat-sinking).
4. logic input : 3 – 5.5V .
5. Automatic current decay mode detection / choice.
6. Mixed with slow current decay mode.

Features:-

• Power supply: DC 24-60 (V).
• Current maximum: 4.5A.
• Output phase current:1 .5A-4.5A.
• Logic input current: 1 0-20mA.
• Optical isolation signal input.
• Output current DIP switch is adjustable.

Features:-

• Good high-speed performance
• Supply voltage: +50VDC
• Output current from 0.5A to 5.6A
• Pulse input frequency up to 200 kHz
• Extremely cost-effective
• Automatic idle-current reduction
• Self-test and Auto-configuration technology TTL compatible and optically isolated input
• Micro step resolutions programmable, from full-step to 102,400 steps/rev
• Suitable for 2-phase and 4-phase motors
• Support PUL/DIR and CW/CCW modes.

Features:-

• Extremely cost-effective.
• Good high speed performance.
• Supply voltage up to 80VAC or +110VDC.
• Output current up to 7.2A.
• Self-adjustment technology.
• Pure-sinusoidal current control technology.
• Pulse input frequency up to 300 KHz.
• TTL compatible and optically isolated input.
• Automatic idle-current reduction.
• 16 selectable resolutions in decimal and binary, up to 51,200 steps/rev.
• Suitable for 2-phase and 4-phase motors.
• Support PUL/DIR and CW/CCW modes.

Features

1. Supply Voltage: 8.2 – 42 VDC.
2. Current Capacity : 2.2A max(24V).
3. Continuous current per phase: 1.5 A.
4. Minimum Logic voltage: 2.5V.
5. Maximum Logic Voltage: 5V.
6. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32.
7. Dimensions : 15 x 20 mm.
8. Weight: 4 gm.

Features

1. Anti-Resonance, provides optimum torque and nulls mid-range instability
2. Motor self-test and parameter auto-setup technology, offers optimum responses with different motors
3. Multi-Stepping allows a low resolution step input to produce a higher microstep output for smooth system performance
4. Microstep resolutions programmable, from full-step to 102,400 steps/rev(Note1)
5. Supply voltage up to 30 VDC
6. Output current programmable, from 0.3A to 2.0A( Note)
7. Pulse input frequency up to 70 KHz
8. TTL compatible and optically isolated input
9. Automatic idle-current reduction
10. Suitable for 2-phase and 4-phase motors.

Features

1. Good high-speed performance
2. Supply voltage up to +50VDC
3. Output current up to 4.2A
4. Pulse frequency up to 300 KHz
5. Automatic idle-current reduction
6. 3-state current control technology
7. Self-adjustment technology
8. Pure-sinusoidal current control technology.

Features:

Features

1. Leadshine original D860H | MA860H microstepping drive.
2. Input voltage :Up to +80VAC or +110VDC.
3. Output current Up to 7.2A.
4. Pulse input frequency up to 300 KHz.
5. Automatic idle-current reduction.
6. Over-voltage, over-current protection.
7. Suitable for 2-phase and 4-phase motors.
8. Support PUL/DIR and CW/CCW modes.
9. Operating Temperature : 70 C.

Features

1. Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
2. USB power supply and peripherals power phase are separate to protect computer security.
3. All the signals are to-isolate which can protect your computer security.
4. 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
5. Wide input voltage range: 12-24V, and with anti-reverse function.
6. One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.

Features

1. Step angle 3.75 degree
2. Phase current: 0.6 ampere
3. Step Angle: 3.75 Degree +/- 5%
4. Drive Sequence: Bipolar
5. Rated Current per Winding: 0.6 A
6. Winding Resistance: 5E5
7. Holding Torque Nm (Kg-cm): 0.064 (0.65)
8. Rotor Inertia (Kg-cm2): 0.015
9. Rated Voltage: Max 40V DC, 12V Typical
10. Flange Size: 56.5 mm.

Features

1. Model : NEMA 17
2. Motor Part Number : JK42HS34-0316
3. Motor Type : Single Shaft
4. Step Angle : 1.8°
5. Holding Torque : 1.6 kg-cm
6. Operating Voltage : 12~16 V
7. Supply Current (A) : 0.31 A/Phase
8. No. of Leads : 6
9. Inductance : 21 mH/Phase
10. Resistance :  38.5 O/Phase
11. Rotor Inertia : 34 gm-cm
12. Weight (gm) : 220
13. Frame Size (mm) : 42 x 42
14. Shaft Diameter (mm) : 5
15. Shaft Length (mm) : 20.

Features

1. Step Angle: 1.8°.
2. Current:  1.5 A /Phase.
3. Holding Torque: 5.5 kg-cm.
4. Detent Torque: 2.6 kg-cm
5. Weight – 360 gm.

Features

1. Comparably more powerful than NEMA17 motors.
2. The input pulse decides the rotation angle of the motor.
3. High accuracy of around 3 to 5% a step.
4. It provides good starting, stopping, and reversing.
5. Control of this motor is less costly because of the exclusion of complex control circuitry.
6. The speed is proportional to the frequency of the input pulses.

Features

1. Step Angle Step Angle: 1.8 °
2. Current: 2.8 A/Phase
3. Holding Torque: 189 N-cm
4. Detent torque: 6.8 N.cm (Maximum)
5. Lead Wires: 4
6. Shaft diameter: 6.35 mm.

Features

1. Step Angle ( ° ): 1.8
2. Motor Length (L)mm: 51
3. Current/Phase A: 1
4. No of Leads: No. 6
5. Shaft type: Round.

Features

1. Step Angle ( ° ): 1.8
2. Motor Length (L)mm: 67
3. Current/Phase A: 5.9
4. No of Leads: No. 4
5. Shaft type: Keyway Type.

Features:-

• Current / Phase: 1.5A
• Step Angle(degrees): 1.8
• Phase: 2
• Type: Hybrid
• Certification: ROHS,CE
• Holding Torque: 4.2 KGCM
• Step angle accuracy: + – 5%(full step, not load)
• Resistance accuracy: + – 10%
• Inductance accuracy: + – 20%
• Temperature rise: 80deg Max(rated current,2 phase on)
• Ambient temperature: -20deg ~+50deg
• Insulation resistance:100M Min,500VDC
• Insulation Strength: 500VAC for one minute
• (Lead Screw).

Features:

Features:

Features:

Features:

Features

1. Supreme finish
2. Smooth surface
3. Long-lasting life
4. Low cost for control achieved
5. High torque at startup and low speeds
6. Ruggedness
7. Simplicity of construction
8. Can operate in an open-loop control system
9. Low maintenance
10. Less likely to stall or slip.

Features

1. Step Angle Step Angle: 1.8 °
2. Current: 4 A/Phase
3. Holding Torque: 460 N-cm
4. Lead Wires: 4
5. Shaft diameter: 14 mm.

Features

1. Rated Voltage:4.2V
2. Current/ phase: 4A
3. Holding Torque: 68 kg-cm
4. Number of Leads: 4
5. Step Angle: 1.8°
6. Step Angle Accuracy: ±5% (full step, no load)
7. Resistance Accuracy: ±10%
8. Inductance Accuracy: ±20%
9. Frame Size: 85x85mm
10. Shaft Length: 32mm
11. Shaft Diameter: 12mm
12. Long-lasting life.

Features

1. Rated Voltage:4.2V
2. Current/ phase: 5A
3. Holding Torque: 87 kg-cm
4.  Number of Leads: 4
5. Step Angle: 1.8°
6. Step Angle Accuracy: ±5% (full step, no load)
7. Resistance Accuracy: ±10%
8. Inductance Accuracy: ±20%
9. Frame Size: 85x85mm
10. Shaft Length: 32mm
11. Shaft Diameter: 12mm.

Features

1. Step Angle Step Angle: 1.8 °
2. Current: 5 A/Phase
3. Holding Torque: 870 N-cm
4. Lead Wires: 4
5. Shaft diameter: 14 mm.

Features

1. Operating voltage :DC 10V-35V
2. Very easy to use, no instructions, all of use are marked on the board
3. With large heat sink to ensure good heat dissipation
4. Input signal high-speed opto-coupler isolation, guarantee not losing steps
5. Semi-flow mode adjustable, semi-flow current adjustable, not the general design on the market, with a variety of semi-flow model and semi-flow current setting function
6. Attenuation model adjusted for all the motors can be locked when no noise
7. Working voltage: DC 10V-35V. Recommend Switching Power Supply DC24V
8. 6N137 high-speed Opto-Coupler, to ensure a high speed without step out.

Features

1. Rated maximum output: ± 4.5A, 40V, Peak 5A, low output impedance, source 0.5?,
2. the receiving end of 0.4?, low voltage shutdown, thermal parking and circulation.
3. circuit protection. After I design, you can set the current output of 0.5A 1A 1.8A 2.5A.
4. 3.3A 4A 4.5A to accommodate more and different motor Current.
5. The drive is suitable software mach2, mach3, (mach3 have support WIN7 system), KCAM4 like.

Features

1. Electrical properties (ambient temperature Tj = 25 pm)
2. Input Power 12 – 36V DC power supply
3. Stepper motor drive current
4. 3A (peak value 3.5A)/axis
5. Drive type
6. Double-pole constant flow PWM actuation output
7. Compatible Stepper motors
8. 2/4 Phase, 4/6/8 leads stepper motors within 3.5A.

Features

1. Support 8 kinds of current control
2. Support 7 kinds of micro steps adjustable
3. The interface adopts high-speed optocoupler isolation
4. Automatic semi-flow to reduce heat
5. Large area heat sink
6. Anti-high-frequency interference ability
7. Input anti-reverse protection
8. Overheat, over current and short circuit protection.

Features

1. ULN2003A motor driver chip
2. Chip all the pins already leads for easy connection to use
3. 5-12V power supply
4. 4-way signal indicator
5. Step angle: 5.625 x 1 / 64
6. Reduction ratio: 1 / 64
7. Phase: 4
8. Current / Phase: 5V.

Features

1. Voltage Max: 16V
2. Maximum current rating: 30 A
3. Practical Continuous Current: 14 A
4. Current sensing available to Arduino analog pin
5. MOSFET on-resistance: 34 mΩ
6. Maximum PWM frequency: 10 kHz
7. Thermal Shutdown
8. Undervoltage and Overvoltage shutdown.