MY6812 100W
Features
- Voltage : 12V
- Rated Power : 120W
- No load current : < 0.55A
- Rate torque : 4.58 KgCm(0.45N.m)
- Rate current : < 7.0A
- Efficiency : >70%
- Shaft diameter: 8 mm (milled groove one-sided 1 mm)
- 100% Ball Bearing construction!
- Speed: 3350RPM.
- Weight: 1.06Kg.
#25 Chain for 6.35mm pitch sproket – Ebike Scooter
Features
| Chain | 25 or 25H |
| Pitch | 6.35mm Pitch Sprockets |
| Link | 141 Links |
| Length | 17.8 inch (Full Length 35.6 inch) |
Attiny 5 Version 2
Features
- Support for the Arduino IDE 1.0 + (OSX/Windows/Linux).
- Power via USB or External Source or 7-16 v to 5 v (automatic selection).
- The On – board, 150 ma 5 v Regulator.
- Built – in USB and serial was debugging).
- 6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB).
STM32F103C8T6 ARM board
Features
- 2.0-3.6V power, I/O.
- Operating voltage:3.3V
- Analog inputs:10
- Digital I/O pins:37
- DC source/sink from I/O pins:6mA
- Flash memory (KB):64/128
- SRAM:20KB
- Frequency (clock speed):72MHz max.
- Communication:I2C, SPI, UART, CAN, USB
Attiny 5 Version 1
Features
- Flash (Kbytes): 8 Kbytes
- Pin Count: 8
- Max. Operating Freq. (MHz): 20 MHz
- CPU: 8-bit AVR
- Number of Touch Channels: 3
- Hardware QTouch Acquisition: No
- Max I/O Pins: 6
- Ext Interrupts: 6
- USB Interface:No
Micro DC 3-6V Submersible Pump Mini water pump
Features
- Operating Voltage : 3 ~ 6V
- Operating Current : 130 ~ 220mA
- Flow Rate : 80 ~ 120 L/H
- Maximum Lift : 40 ~ 110 mm
- Continuous Working Life : 500 hours
- Driving Mode : DC, Magnetic Driving
Vibrator Motor Button Type
Features
- Voltage Range: DC 2.5-4V.
- Motor Diameter: 10 mm.
- Motor Thickness: 3.4 mm.
- Min. Rated Speed: 9000RPM
- Max. Rated Current: 90mA
Coreless Motor + Propeller 7×20
Features
- Model: 8520
- Shaft Size: 1.0 mm
- Rated Voltage: 3.7 V. @ 0.12A
- Rated RPM: 50000.
- Wire Length: 6cm
- Prop. Length: 55 or 65 mm
Motor Type 3V-4.5V Cell Phone Micro Vibrator
Features
- Rated Voltage: DC 3V
- Speed: 10000RPM
- Body Size : 6 x 12 mm / 0.24″ x 0.47″ (D*H) (Approx.)
- Wire Length : 30mm /1.2″
- Total Length : 18mm/ 0.47″
- Main Color : Silver Tone
- Material : MetalThis is a tiny vibration motor. Use it to provide vibrational alerts.
DC 3.7V 7mm x 16mm Magnetic Micro Coreless Motor + Propeller
Features
- Fiber Glass Material
- No batteries Battery
- Non Rechargeable
- Width x Height: 30 mm x 40 mm
8520 8.5x20mm Coreless Motor + 75mm Propeller for Micro FPV RC Quadcopter
Features
- Model: 8520
- Shaft Size: 1.0 mm
- Rated Voltage: 3.7 V. @ 0.12A
- Rated RPM: 50000.
- Wire Length: 6cm
- Prop. Length: 55 or 65 mm
Blade Propeller for 8520 8.5x20mm
Features
- Material: Glass Fiber.
- Total Length: 55 mm.
- Propeller diameter (ID): 2.9 mm.
-
Color: Black & Red.
- Durable plastic construction
- Strong and lightweight
Arduino Nano
Features
- Microcontroller Atmel ATmega328 SMD Package
- Operating Voltage (logic level) 5 V
- Input Voltage (recommended) 7-12 V
- Input Voltage (limits) 6-20 V
- Digital I/O Pins 14 (of which 6 provide PWM output)
- Analog Input Pins 8
- DC Current per I/O Pin 40 mA
- Flash Memory 32 KB (of which 2KB used by bootloader)
- SRAM 2 KB
- EEPROM 1 KB
- Clock Speed 16 MHz
- Dimensions 0.70” x 1.70”
Arduino Uno
Features
Microcontroller : ATmega328 SMD.
Operating Voltage : 5V.
Supply Voltage recommended : 7-12V DC.
Digital I/O Pins : 14 (of which 6 provide PWM output).
Analog Input Pins : 6.
DC Current per I/O Pin : 40 mA.
Arduino Sensor Shield
Features
- Retain the merits of the V4.0 version
- Laminated design
- PCB immersion gold processing technology
- IIC interface
- Bluetooth module communication interface
- SD card module communication interface
Prototype Shield For UNO
Features
- It has a nice standard 0.1″x0.1″ prototying grid with big pads
- Comes with Stacking headers and plain header, choose whichever you want when soldering together
- A IC pattern for adding DIP ICs up to 20 pins
- Power rails down the middle and sides
- A reset button and an extra general use button
- 2 3mm general use LEDs, red and green, as well as 2 matching resistors
Nano V3 Ethernet Shield
Features
- ENC28J60 Ethernet chips, SOP28 package
- SPI Interface
- 1×10 connector, can be easily mounted with the MCU
- Built-in isolation transformer RJ45 connectors HR911105A
- Power LED
- Single Supply: +3.3 V
- 25Mhz Crystal
- PCB size: 48×18 mm
NANO / UNO Multi-Purpose Expansion Board
Features
- Compatible with Arduino NANO.
- All digital and analog pins breakout.
- Compact size.
- External power supply current support.
- Leads all pins out, convenient for wiring and doing experiments.
L298P Motor Shield motor driver
Features
- L298P based Arduino motor driver shield
- Onboard Buzzer (D4).
- Onboard Bluetooth interface, you can directly plug, no wiring required.
- Six Analog interface.
- Forward, Backward steering indicators
L293 Motor Driver Shield
Features
- 2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer
- 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC.
- Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5% resolution)
- Up to 2 stepper motors (unipolar or bipolar) with single coil, double coil or interleaved stepping.
USB Host Shield
Features
- Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards.
- Operates over the extended -40C to +85C temperature range
- Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host)
- Supports HID devices, such as keyboards, mice, joysticks, etc.
Ethernet Shield
Features
- Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet.
- Stackable Design, can directly be supported by for Arduino official Ethernet Library.
- Supports up to four simultaneous socket connections
- Can be used to store files for serving over the network.
- Compatible with the for Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560)
ESP8266 WIFI Shield
Features
- Open source IoT Platform
- Easily Programmable
- Low cost & Simple to Implement
- WI-FI enabled
Data Logger Shield
Features
- SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents possible damage to your SD card.
- Real time clock (RTC) keeps the time going even when the Arduino is unplugged. The battery backup lasts for 2 years.
- Included libraries and example code for both SD and RTC mean you can get going quickly.
- Prototyping area for soldering connectors, circuitry or sensors.
Arduino CNC Shield
Features
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- Supports PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- Supports Coolant enable
UNO R3 acrylic Case
Features
- Weight: 53 gm.
- Dimensions : 79.5 x 64.5 x 21 mm.
- Material: A grade acrylic sheet.
- For UNO R3 Development Board only.
- With screw copper pillar and installation instructions.
- To protect your little computer against damages, dust and scratches Clear Top and Bottom.
- This case provides easy access to all ports.
XBEE Shield
Features
- Stackable design, easy to plug into the ARDUINO development board.
- 3.3v and 5v dual power output.
- 3.3v and 5v IO compatible.
- USB 2.0 protocol.
- Bitbang mode ready.
- Easily connected to a PC via mini USB Cable.
- XBee-setting support software X-CTU.
16/2BLUE LCD Shield
Features
- Blue Backlight with white words
- uses 4 Bit Arduino LCD Library
- Left, Right, Up, Down and Select buttons
- Screen contrast adjustment
- Arduino Reset button
- Operating Voltage is 5V
Wemos D1 R2 WIFI ESP8266 Shield Arduino
Features
- Based on the ESP-8266EX.
- Arduino Compatible, you can use it on Arduino IDE.
- NodeMcu Compatible
49TYD-500 Synchronous 5 RPM AC220/240V AC Motor
Features
- 49TYD-500 Synchronous AC Motor
- Voltage – 220/240V AC 50/60 HZ
- Type – Synchronous
- Power – 4 W
- RPM – 5/6 RPM
Wanhao Duplicator I3 Mini FDM 3d Printer
Features
- Printing Technology: FFF (Fused Filament Fabrication)
- Build Volume: 120L X 135W X 100H
- Filament Compatibility: PLA, PET-G, Carbon Fiber, HIPS, Metal Fill
- Layer Resolution: 100-400 microns
- Software & Firmware: Cura, Matter Control, Simplify 3D
100K OHM NTC Thermistors For Reprap 3D Printer
Features
- Temperature range of use: −40°C to 270°C.
- Dissipation power factor: ≥5 mW/℃ (static in the air).
- 100k Ohm NTC Thermistor.
- NTC Thin Film Thermistor Cable.
- Max power rating: 45 mW
- The hot time constant: ≤7 s(in the air)
SC10UU Linear Slide / Motion Bearing / Block
Features
- Product Name: Linear Bearing
- Model: SC10UU
- Material: Metal, Rubber
- ID: 10mm.
MK2B PCB Heatbed 12V/24V
Features
- 2 layer, 35μm copper
- Copper plated holes
- The resistance between 1.0 and 1.2 ohm
- Active heated area: 200 mm x 200 mm.
- 209 mm center-to-center mounting holes (outside the active area).
- Support 12V, 24V power.
- Double-sided, the other side is no wiring, heating uniformity, smooth printing.
- Regardless of the positive and negative terminal, you can free wiring
Prusa i3 RepRap 3D Printer DIY Kit (Unassembled)
Features
- UPGRADED ENDER 3
- EASY TO ASSEMBLE
- SAFETY PROTECTED POWER SUPPLY
- ADVANCE TECHNOLOGY
- RESUME PRINT
Prusa i3 3d Printer DIY Kit Aluminium Structure ( Unassembled )
Fully Assembled RAMPS Board (RAMPS-35 volts + AT Mega + 5*A4988 Polulo Stepper Drivers) with FAN MOUNTS for cooling RAMPS3 x Mechanical End Stops01 x Mk 2 Heated Bed5 x NEMA 17 Motors ( Brand -Kysan 1124090 – 5.5 N.cm Torque)12V ATX Power Supply Unit (Brand – Intex) – Modified to be plug and play.All wires and connectorsAdditional cooling fans with mounts. All Steel & threaded rods for X, Y & Z (We use high precision Carbon Steel Rods for Smooth Rods, these rods do not have any lag in the linear bearings LM8UU due to this the printing performance increases greatly). We request all our customers to make sure that smooth rods have no lag with the linear bearings (if they purchase from other sources)