TB6560 CNC 3 Axis Stepper Motor Driver Controller Board For Mach3 KCAM4 EMC2 36V
Features
- Electrical properties (ambient temperature Tj = 25 pm)
- Input Power 12 – 36V DC power supply
- Stepper motor drive current
- 3A (peak value 3.5A)/axis
- Drive type
- Double-pole constant flow PWM actuation output
- Compatible Stepper motors
- 2/4 Phase, 4/6/8 leads stepper motors within 3.5A.
VNH2SP30 – Monster Moto Shield 30A Mini Stepper Motor Driver
Features
- Voltage Max: 16V
- Maximum current rating: 30 A
- Practical Continuous Current: 14 A
- Current sensing available to Arduino analog pin
- MOSFET on-resistance: 34 mΩ
- Maximum PWM frequency: 10 kHz
- Thermal Shutdown
- Undervoltage and Overvoltage shutdown.
ULN2003 Driver
Features
- ULN2003A motor driver chip
- Chip all the pins already leads for easy connection to use
- 5-12V power supply
- 4-way signal indicator
- Step angle: 5.625 x 1 / 64
- Reduction ratio: 1 / 64
- Phase: 4
- Current / Phase: 5V.
TB6600
Features
- Support 8 kinds of current control
- Support 7 kinds of micro steps adjustable
- The interface adopts high-speed optocoupler isolation
- Automatic semi-flow to reduce heat
- Large area heat sink
- Anti-high-frequency interference ability
- Input anti-reverse protection
- Overheat, over current and short circuit protection.
tb6560
Features
- Operating voltage :DC 10V-35V
- Very easy to use, no instructions, all of use are marked on the board
- With large heat sink to ensure good heat dissipation
- Input signal high-speed opto-coupler isolation, guarantee not losing steps
- Semi-flow mode adjustable, semi-flow current adjustable, not the general design on the market, with a variety of semi-flow model and semi-flow current setting function
- Attenuation model adjusted for all the motors can be locked when no noise
- Working voltage: DC 10V-35V. Recommend Switching Power Supply DC24V
- 6N137 high-speed Opto-Coupler, to ensure a high speed without step out.
MACH3 interface board
Features
- Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software.
- USB power supply and peripherals power phase are separate to protect computer security.
- All the signals are to-isolate which can protect your computer security.
- 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc.
- Wide input voltage range: 12-24V, and with anti-reverse function.
- One relay output control interface, accessed by the spindle motor or the air pump, water pump, etc.
Leadshine DMA860H
Features
- Leadshine original D860H | MA860H microstepping drive.
- Input voltage :Up to +80VAC or +110VDC.
- Output current Up to 7.2A.
- Pulse input frequency up to 300 KHz.
- Automatic idle-current reduction.
- Over-voltage, over-current protection.
- Suitable for 2-phase and 4-phase motors.
- Support PUL/DIR and CW/CCW modes.
- Operating Temperature : 70 C.
Leadshine DM542
Features
- Good high-speed performance
- Supply voltage up to +50VDC
- Output current up to 4.2A
- Pulse frequency up to 300 KHz
- Automatic idle-current reduction
- 3-state current control technology
- Self-adjustment technology
- Pure-sinusoidal current control technology.
Leadshine DM320C
Features
- Anti-Resonance, provides optimum torque and nulls mid-range instability
- Motor self-test and parameter auto-setup technology, offers optimum responses with different motors
- Multi-Stepping allows a low resolution step input to produce a higher microstep output for smooth system performance
- Microstep resolutions programmable, from full-step to 102,400 steps/rev(Note1)
- Supply voltage up to 30 VDC
- Output current programmable, from 0.3A to 2.0A( Note)
- Pulse input frequency up to 70 KHz
- TTL compatible and optically isolated input
- Automatic idle-current reduction
- Suitable for 2-phase and 4-phase motors.
DRV8825
Features
- Supply Voltage: 8.2 – 42 VDC.
- Current Capacity : 2.2A max(24V).
- Continuous current per phase: 1.5 A.
- Minimum Logic voltage: 2.5V.
- Maximum Logic Voltage: 5V.
- Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Dimensions : 15 x 20 mm.
- Weight: 4 gm.
A4988
Features
- Supply Voltage : 8-35 VDC.
- Current : 1.0A (no heatsink ).
- Current : 2.0A (with heat-sinking).
- logic input : 3 – 5.5V .
- Automatic current decay mode detection / choice.
- Mixed with slow current decay mode.
Stepper Motor NEMA 34 87 kg-cm
Features
- Rated Voltage:4.2V
- Current/ phase: 5A
- Holding Torque: 87 kg-cm
- Number of Leads: 4
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 32mm
- Shaft Diameter: 12mm.
NEMA 17 1.6 kgcm
Features
- Model : NEMA 17
- Motor Part Number : JK42HS34-0316
- Motor Type : Single Shaft
- Step Angle : 1.8°
- Holding Torque : 1.6 kg-cm
- Operating Voltage : 12~16 V
- Supply Current (A) : 0.31 A/Phase
- No. of Leads : 6
- Inductance : 21 mH/Phase
- Resistance : 38.5 O/Phase
- Rotor Inertia : 34 gm-cm
- Weight (gm) : 220
- Frame Size (mm) : 42 x 42
- Shaft Diameter (mm) : 5
- Shaft Length (mm) : 20.
Stepper Motor NEMA 34 68 kg-cm Hybrid Bipolar
Features
- Rated Voltage:4.2V
- Current/ phase: 4A
- Holding Torque: 68 kg-cm
- Number of Leads: 4
- Step Angle: 1.8°
- Step Angle Accuracy: ±5% (full step, no load)
- Resistance Accuracy: ±10%
- Inductance Accuracy: ±20%
- Frame Size: 85x85mm
- Shaft Length: 32mm
- Shaft Diameter: 12mm
- Long-lasting life.
Stepper Motor NEMA 34 122 kg-cm Hybrid Bipolar
Features
- Supreme finish
- Smooth surface
- Long-lasting life
- Low cost for control achieved
- High torque at startup and low speeds
- Ruggedness
- Simplicity of construction
- Can operate in an open-loop control system
- Low maintenance
- Less likely to stall or slip.
Stepper Motor NEMA 34 46 kg-cm Hybrid Bipolar
Features
- Step Angle Step Angle: 1.8 °
- Current: 4 A/Phase
- Holding Torque: 460 N-cm
- Lead Wires: 4
- Shaft diameter: 14 mm.
NEMA 34 34 kg-cm
Features
- Step Angle ( ° ): 1.8
- Motor Length (L)mm: 67
- Current/Phase A: 5.9
- No of Leads: No. 4
- Shaft type: Keyway Type.
NEMA 23 7.2 kg-cm
Features
- Step Angle ( ° ): 1.8
- Motor Length (L)mm: 51
- Current/Phase A: 1
- No of Leads: No. 6
- Shaft type: Round.
NEMA 23 18.9 kg-cm
Features
- Step Angle Step Angle: 1.8 °
- Current: 2.8 A/Phase
- Holding Torque: 189 N-cm
- Detent torque: 6.8 N.cm (Maximum)
- Lead Wires: 4
- Shaft diameter: 6.35 mm.
NEMA 23 10.1 kg-cm
Features
- Comparably more powerful than NEMA17 motors.
- The input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- It provides good starting, stopping, and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
Stepper Motor NEMA 34 87 kg-cm Hybrid Bipolar
Features
- Step Angle Step Angle: 1.8 °
- Current: 5 A/Phase
- Holding Torque: 870 N-cm
- Lead Wires: 4
- Shaft diameter: 14 mm.
Minebea 16PU-M202 Bipolar Stepper Motor
Features
- Step angle 3.75 degree
- Phase current: 0.6 ampere
- Step Angle: 3.75 Degree +/- 5%
- Drive Sequence: Bipolar
- Rated Current per Winding: 0.6 A
- Winding Resistance: 5E5
- Holding Torque Nm (Kg-cm): 0.064 (0.65)
- Rotor Inertia (Kg-cm2): 0.015
- Rated Voltage: Max 40V DC, 12V Typical
- Flange Size: 56.5 mm.
NEMA 17 5.5 kgcm
Features
- Step Angle: 1.8°.
- Current: 1.5 A /Phase.
- Holding Torque: 5.5 kg-cm.
- Detent Torque: 2.6 kg-cm
- Weight – 360 gm.
5V step motor 28BYJ-48-5V
Features
- Rated voltage: 5V DC
- Reduction Ratio: 64:1
- Step Angle: 5.625° /64
- Frequency: 100Hz
- Self-positioning Torque: >34.3mN.m
- Friction torque: 600-1200 gf.cm
- Pull in torque: 300 gf.cm.
5V step motor 28BYJ-48-ULN2003
Features
- Rated voltage: 5V DC
- Reduction Ratio: 64:1
- Step Angle: 5.625° /64
- Frequency: 100Hz
- Self-positioning Torque: >34.3mN.m
- Friction torque: 600-1200 gf.cm
- Pull in torque: 300 gf.cm.
9v 200ma
Features
- Quality custom-design solar energy panel
- The solar cells are encased and protected by a durable outer poly frame
- Polycrystalline solar cells
- Max output power: 1.8W
- Max power voltage: 9V
- Max power current: 200mA
- Open circuit voltage: 10.8v
- Short circuit current: 220mA
- Small Epoxy Solar Panels are simple to install or add to your existing product.
- Construction requires no frame or special modifications
- Small space required for installation.
9v 100mA
Features
- Quality custom-design solar energy panel
- The solar cells are encased and protected by a durable outer poly frame
- Polycrystalline solar cells
- Max output power: 1.08W
- Max working voltage: 9.9V
- Max charging current: 110mA
- Min output power: 0.9W
- Min working voltage: 9V
- Min charging current: 100mA.
6v 80ma
Features
- 100% new high quality.
- 6 volt 80ma polycrystalline solar panel
- High conversion speed, high-efficiency output.
- Excellent low light effect.
- High transmittance tempered glass.
- A unique technique to prevent water frozen within the deforming framework.
- Small Epoxy Solar Panels are simple to install or add to your existing product.
- Construction requires no frame or special modifications
- Small space required for installation.
6v 540ma
Features
- Poly crystalline solar cells
- Max output power (without load): 3.23W
- Max working voltage (without load): 6.6V
- Max charging current (without load): 540mA
- Min output power (without load): 3.2W
- Min working voltage (without load): 6V
- Small Epoxy Solar Panels are simple to install or add to your existing product.
- Construction requires no frame or special modifications
- Small space required for installation.
- Has 2 to 3 times the power of amorphous thin-film solar panels
- Ready to use, they require no frame or special modifications.
- For connection, just solder or crimp to the copper tape.
- Dimension: 23.3 X 11.5 Cm Thickness 3mm +/- 2 mm.
6v 300mA
Features
- Max output power: 3.23W
- Max working voltage: 6.6V
- Max charging current: 490mA
- Min output power: 2.7W
- Min working voltage: 6V
- Min charging current: 450mA
- Small Epoxy Solar Panels are simple to install or add to your existing product
- Construction requires no frame or special modifications
- Small space required for installation.
- Has 2 to 3 times the power of amorphous thin-film solar panels
- Ready to use, they require no frame or special modifications.
- For connection, just solder or crimp to the copper tape.
6v 200mA
Features
- Polycrystalline solar cell
- Max output power: 1.1W
- Max working voltage: 6.6V
- Max charging current: 110mA
- Min output power: 0.6W
- Min working voltage: 6V
- Min charging current:200mA
- Small Epoxy Solar Panels are simple to install or add to your existing product
- Construction requires no frame or special modifications
- Small space required for installation.
6v 100mA
Features
Best in Class conversion efficiency
Anti-reflective coating for more light absorption
Optically, mechanically and electrically tested
Dimension : 88x 55mm
40W solar panel
Features
- Max Power at STC: 30W
- Short Circuit Current : 1.70A
- Optimum Operating Current : 1.60A
- Open Circuit Voltage : 22.9V
- Opitmum Operating Voltage : 19.5V
- Operating Temperature: -40ºC to 90ºC.
3v 300mA
Features
- Quality custom-design solar energy panel
- Max output power (without load): 0.45W
- Max working voltage (without load): 3.3V
- Max charging current (without load): 150mA
- Min output power (without load): 0.45W
- Min working voltage (without load): 3V
- High conversion speed, high-efficiency output.
- Excellent low light effect.
- A+ Grade, anti PID Poly Crystalline cell.
3v 150ma
Features
Best in Class conversion efficiency
Anti-reflective coating for more light absorption
Optically, mechanically and electrically tested
Dimension : 72 x 45 mm
20W solar panel
Features
- Output Power: 20 Watts
- Operating Voltage: 12 Volt
- Wattage (Wp): 20
- Voltage at Max Power: 18.20 volts
- Current at Max Power: 1.10 amps
- Open Circuit Voltage: 22.40 volts
- Short Circuit Current: 1.45AL