2*3 Size inch
Features
- Size: 3 Inches * 2 Inches
- Thickness: 1.5mm
- PCB Type: DOT PCB
- PCB Material: Phenolic
- Hole Spacing: 2.54mm
- PCB Dimension: 75*50mm
- Weight: 25g.Perforated
6x6x6mm Tactile 4 Pin Push Button Switch – 5 Pieces Pack (Copy)
6x6x6mm Tactile 4 Pin Push Button Switch is widely used as a standard input “buttons” on electronic projects. These work best when you mount it on PCB but can also be used on a solderless breadboard for temporary connections in prototypes. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed and complete the circuit.
This tactile switch also offers reliable dome contact technology and strong tactile feedback, with multiple operating forces to choose from. Applications include telecommunications, consumer electronics, audio/visual, medical devices, testing/instrumentation, and computer/peripherals.
They come in a pack of 5, as they’re pretty handy so you’ll want to keep them around.
Red TTP223 Touch button Module
Features
- Supports momentary or latching/toggle modes.
- Supports Active High or Active Low output signal modes.
- Dimensions : 15mm x 11mm.
- Input Voltage : 2 Volt – 5.5 Volts DC.
- The response time max ~ 60mS in fast mode, ~220mS at low power mode @VDD=3V.
- Sensitivity can adjust by the capacitance(0~50pF).
- Have two kinds of sampling length by pad option(SLRFTB pin).
- Stable touching detection of the human body for replacing traditional direct switch key.
- Provides Fast mode and Low Power mode selection by pad option(LPMB pin).
- Provides direct mode、toggle mode by pad option(TOG pin).
- Open drain mode by bonding option, OPDO pin is open drain output, Q pin is CMOS output.
- All output modes can be selected active high or active low by pad option(AHLB pin).
- Have the maximum on time 100sec by pad option(MOTB pin).
- Have external power-on reset pin(RST pin).
Voltage sensor Module
Features
- You can also use the IICLCD1602 LCD to display voltage.
- By 3P connector, connect this module with the expansion of board Arduino
- Voltage input range: DC 0-25 V
- Voltage detection range: DC 0.02445 V to 25 V
- Voltage analog resolution : 0.00489 V
650NM Laser Diode
Features
- Output Power: 5mW
- Working Voltage: 5V DC
- Working temperature: -10 ℃~＋40 ℃
- Housing material: Copper
- Working life: more than 2000 hours
- Spot mode: Dot Facula (continuous output)
- Laser wavelength: 650nm red-colored.
- Operating current: <40mA
- Power lead length: 120mm.
Motor Type 3V-4.5V Cell Phone Micro Vibrator
Features
- Rated Voltage: DC 3V
- Speed: 10000RPM
- Body Size : 6 x 12 mm / 0.24″ x 0.47″ (D*H) (Approx.)
- Wire Length : 30mm /1.2″
- Total Length : 18mm/ 0.47″
- Main Color : Silver Tone
- Material : MetalThis is a tiny vibration motor. Use it to provide vibrational alerts.
Female to Female Jumper wires
Features
- Length: 20cm
- Quantity: 10pcs
- 1p -1p pin female to female header
- Compatible with 2.54mm spacing pin headers
Cartoon ultrasonic sensor fixing bracket
Features
- Acrylic Body.
- Easy to install.
- compatible with HC-SR04
9v Battery for Robotics Projects
QUICK OVERVIEW
Constant 9V Output till lasts
Metal Jacket Body
Good Built Quality and hence Leakproof
Easy to install and Replace
Corrosion free Connector Point for long-term use
0% Mercury and Cadmium. Environment-friendly
OEM Compatible.
Water Level Sensor
Features
- Operating voltage: DC3-5V
- Operating current: less than 20mA
- Sensor Type: Analog
- Detection Area: 40mmx16mm
- Operating temperature: 10℃-30℃
- Humidity: 10% -90% non-condensing.
18650 MODULE
Features
- Dimension: 25 x 19 x 10 (LxWxH)mm.
- Input interface: micro USB.
- Current Protection: Yes
- Charging mode: Linear charging.
- Current: 1A adjustable.
- Charge precision: 1.5%.
- Input voltage: 4.5V-5.5V.
- Full charge voltage: 4.2V.
Micro TP4056 USB5.5V/1A Lithium Battery Charger
Features
- Dimension: 25 x 19 x 10 (LxWxH)mm.
- Input interface: micro USB.
- Current Protection: Yes
- Charging mode: Linear charging.
- Current: 1A adjustable.
- Charge precision: 1.5%.
- Input voltage: 4.5V-5.5V.
- Full charge voltage: 4.2V.
WS2812 Breakout Board
Features
- The control circuit and the LED share the only power source.
- Control circuit and RGB chip are integrated into a package of 5050 components, form a complete control of pixel point.
- Built-in signal reshaping circuit, after wave reshaping to the next driver, ensure waveform distortion not accumulate.
- Built-in electric reset circuit and power lost reset circuit.
- Each pixel of the three primary colors can achieve 256 brightness levels, or 16M colors full-color display, and scan frequency not less than 400Hz/s.
- Cascading port transmission signal by a single line.
- Any two points the distance more than 5m transmission signal without any increase circuit.
- When the refresh rate is 30fps, cascade number is not less than 1024 points.
- Send data at speeds of 800Kbps.
- The color of the light was highly consistent
CH375B U-DISK read write module USB interface communication spi interface
Features:
- CH375B with the 8-bit data bus and read, write, chip select control lines and interrupt output can be easily attached to the system bus of the microcontroller/DSP/MCU/MPU controller.
- USB host mode, CH375B provides serial communication via serial input, serial output, and interrupt output monolithic/DSP/MCU/MPU connected.
- 28 connector, easy with the MCU mount.
- Jumper selectable can work in parallel or serial mode.
- USB status indicator.
- On board 3.3 V LDO 1117, provides 800 mA current.
- Color: Blue.
MK8 Extruder Drive Gear 26Teeth 11x11mm
This is a 26 Tooth Extruder Drive Gear that fits into extruder assemblies and firmly grips the 3D Printing Filament to move it towards or away from the hotend assembly. It is capable of high torque without damaging the filament, and fits directly onto the shaft of NEMA 17 Stepper Motors, making it simple to install but effective at assisting with consistent extrusion.
These particular Extruder Drive Gears are made for the All type of 3D printer extruders and ensure that the filament is moved into the melt zone when extrusion is happening while pulling it back when the hotend is moving across the print bed. This translates to smooth and consistent extrusion, with improved print quality, and reduces the chances of clogging or similar problems. Although this is a basic little part, it is a vital part of the extruder system and counteracts the back-pressure of the melted filament within the hotend assembly.
Typical Applications For The Extruder Drive Gear is for extruder Drive Gear is designed to fit the TEVO Tarantula, but could be used on many other similar 3D Printers, or even in different machines altogether. It is made from brass, which is durable but soft enough to prevent filament damage, and has a tiny form factor to easily fit without requiring any extra modifications.
Pneumatic Connectors 1.75mm PTFE Tube quick coupler j-head Hotend Fitting
Pneumatic Coupler Air Connectors PC4-M10 4MM Straight Fitting For PTFE Bowden Tube 3D Printer push to connect fitting for 4mm OD tubing, NPT 1/8″ thread. This item is often used in 3d printers to connect Bowden tubing to the extruder and to the hot end. This fitting has a 4.3mm output hole, so the tubing can be fixed into the connector.
The Pneumatic Coupler Air Connectors PC4-M10 4MM Straight Fitting For PTFE Bowden Tube 3D Printer is designed for polyurethane or nylon tubing. Made of nickel-plated brass for corrosion resistance. Even after installation, the direction of the tube can be changed freely.
Oval release ring assists to connect the hose easily by manual, without special tools required. Outside (and inside available) hexagon wrench.
12x12x6mm Tactile 4 Pin Push Button Switch – 5 Pieces Pack
12x12x6mm Tactile 4 Pin Push Button Switch is widely used as a standard input “buttons” on electronic projects. These work best when you mount it on PCB but can also be used on a solderless breadboard for temporary connections in prototypes. The pins are normally open (disconnected) and when the button is pressed they are momentarily closed and complete the circuit.
This tactile switch also offers reliable dome contact technology and strong tactile feedback, with multiple operating forces to choose from. Applications include telecommunications, consumer electronics, audio/visual, medical devices, testing/instrumentation, and computer/peripherals.
They come in a pack of 5, as they’re pretty handy so you’ll want to keep them around.
PAM8403 Version 2
Features
- Dual channel stereo output 3 w + 3 w power Class D
- Works with 2.5V-5v power supply
- High amplification efficiency 85%
- can directly drive 4 O/8 O small speakers
- Good sound quality & noise suppression
- Unique without LC filter class D digital power board
- Can use computer USB power supply directly
- Small Size, 1.85 x 2.11 cm can easily fit in a variety of products
Mini Breadboard 170 Points
Features
- Tie-points: 170 (10×17)
- Size: 48 x 35 x 10 mm(LxWxH).
- Use: experimental, testing, robot
- Matching jumper, diameter 0.8mm
- Phosphor bronze nickel plated spring clips
- Accepts a variety of wire sizes (29-20 the AWG)
MAX485 TO TTLL Module
Features
- On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver.
- A low power consumption for the RS-485 communication
- Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring.
- Slew-rate limited transceiver
- All pins of the chip have been lead to can be controlled through the microcontroller.
- Convenient RS-485 communication wiring
- Multiple Units can be connected to the same RS-485 bus wiring.
- All Chip pins are brought out for proper controls
IR LED Sensor
Features
- Detection distance: 2 ~ 30cm
- Detection angle: 35 °
- Comparator chip: LM393
- 3mm screw holes for easy mounting
TTP223 1way
Features
- Power supply voltage(VCC): 2.0, 3, 5.5 V.
- Output high VOH: 0.8VCC V
- Output low VOL: 0.3VCC V
- Response time (touch mode) : 60 mS
- Response time (low power mode) : 220 mS
- Can replace the traditional touch of a button
- Four M2 screws positioning holes for easy installation.
USB for DIY charger 5V step-up power module lithium battery charging board
Features:
- BAT Discharging Stop Voltage:2.9V
- Discharging Efficiency:85%(input 3.7V output 5V/1A)
- Charging and discharging indication
- Internally installed charging and discharging power MOS
- Preset 4.2V charging voltage, precision ±1%
- Max 8uA standby current
- Integration charging management and discharging management
- Intelligent temperature control and overtemperature protection
- Integration output overvoltage protection, short circuit protection, overload protection.
RFID Tag Key Fob Keyfobs 125Khz
Feature
- Material: ABS
- Response Frequency: 125Khz
- 2kbps ASK
- Diameter: ~29mm
- Range: 0-10 cm
- Manchester encoding
- 32-bit unique ID
- Uses TK4100 chip which is compatible with EM4100
- 64-bit data stream [Header+ID+Data+Parity]
- Read Time: 1-2ms.
10 segment led bargraph light display red, yellow, green, blue
Features:
- built-in chip.
- 5050 Highlight LED.
- It is equipped with an I / O interface that can control multiple LEDs.
- it can finish data reception and decoding in one piece.
- RGB 256 level brightness adjustment, 160,000 color image display effect, sweep frequency not less than 400Hz / S.
NE555 Pulse Module
Features
- Input Voltage: 5V-15VDC
- Output amplitude: 4.2V V-PP to 11.4V V-PP.
- Output Current : 15mA for 5V & 35mA for 12V.
- Color: Blue
- Working voltage: 5-12V
- Size: 25x 13 x 12 mm (LxWxH)
- Minimum – 50% duty cycle, 3.7 Hz & Maximum – 98% duty cycle, 1.3KHz
Dean Connector
Features
- Material: plastic and metal (gold plated)
- Improved Locking.
- Gold Plated Connectors tip.
- Color: Red.
- High-Quality built and Material.
- Good resistance to Temperature & High Amp. Current.
Heart beat Sensor
Features
- Use IR LED and an optical transistor to detect pulsation in fingers
- Small and Compact module
- Easy to use.
PAM8403 Version 1
Features
- Dual channel stereo, high output power (3 w + 3 w power @ 5V and 4 ohms load)..
- Double panel wiring solves crosstalk.
- Super mini design allows it to be easily placed in a variety of digital products.
- 3W Output at 10% THD with a 4ΩLoad and 5V Power Supply.
- Filterless, Low Quiescent Current and Low EMI and Low Noise.
- Short Circuit Protection and Thermal Shutdown
0.5mm 3D Printer Extruder Brass Nozzle PR57
0.5mm 3D Printer Extruder Brass Nozzle Makerbot which has outstanding quality and the best performance for DIY and professional systems. By simply adding a holder, you can assemble your own dual head extrusion.
LDR Module
Features
- LM393 based design.
- Can detect ambient brightness and light intensity.
- Adjustable sensitivity (via blue digital potentiometer adjustment).
- Output Digital – 0V to 5V, Adjustable trigger level from preset.
- LEDs indicating output and power.
- Operating Voltage: 3.3V to 5V DC.
- Operating Current: 15ma.
1 Chanel 5v Relay Module for Arduino
Features:
- Trigger Voltage: 5 VDC
- Trigger Current : 20 mA
- Maximum Switching Voltage: 250VAC@10A; 30VDC @10A
- Single Pole Double Throw (SPDT) Configuration
- Power supply indicator lamp.
Vibrator Motor Button Type
Features
- Voltage Range: DC 2.5-4V.
- Motor Diameter: 10 mm.
- Motor Thickness: 3.4 mm.
- Min. Rated Speed: 9000RPM
- Max. Rated Current: 90mA
TCRT5000 Module
Features
- The working voltage: 5V
- A fixed bolt hole for easy installation
- Build-in Tcrt5000 Sensor NSOR
- Applicable to a variety of platforms including Arduino / AVR / ARM /PIC
SG90 Servo Motor Bracket SG90 9g Bracket Support
Features:
- Material: Mild Steel(MS)
- Weight: 5 gm (each)
- Length: 35 mm
- Width: 37 mm
- Thickness: 2.7 mm.
TAP Sensor Module
Features
| Brand/Manufacturer | Generic |
| Country Of Origin | China |
| Packer / Importer Address | Constflick Technologies Limited, Building No 13 and 14, 3rd Floor, 2nd Main, Siddaiah Road, Bangalore, Karnataka – 560027 India. |
| MRP | Rs. 55.46 (Inclusive of all Taxes) |